Posted in

Can blocking diodes cause voltage drop in a PV system?

Hey there, fellow solar nerds and PV system designers — let’s cut to the chase: if you’ve ever been tinkering with a residential or commercial solar setup, you’ve probably wondered if those blocking diodes are stealing volts right out of your system. I’m Jake, and I’ve been selling PV diodes for 8 years now, working directly with installers, system owners, and even a few solar newbies who swear their panels aren’t performing like they should. Today, we’re diving deep into this question that’s haunted more than a few of us: Can blocking diodes cause voltage drop in a PV system? Solar Photovoltaic Diode Module

First, let’s keep it real — no fancy jargon that makes your eyes glaze over. Blocking diodes in PV systems? Their whole job is simple: stop current from flowing backward when the sun goes down (or when one shaded panel is producing less power than the string next to it). Without ‘em, your whole string of panels would basically become a big battery and drain power back into the weaker one at night. That’s bad news — we’ve all seen the graph of overnight voltage drop before, and it’s not pretty. But here’s the thing I tell every new customer who calls me panicking about low output: diodes can cause voltage drops, but it’s not the kind that’s killing your system’s performance if you pick the right ones and install ‘em correctly.

Wait, let’s break down how diodes even work in plain terms. A diode, whether it’s the old-fashioned through-hole type or the power Schottky diodes we sell at my module, lets current flow one way only. But here’s the inherent quirk: when current crosses a diode, there’s a small voltage “hit” — that’s called forward voltage drop, and it’s non-negotiable for any semiconductor. For regular silicon diodes, that’s usually around 0.7V per unit. For power Schottky diodes (the good ones for PV), it’s lower — like 0.3V or less. That’s where a lot of confusion comes in: some installers see that 0.3V and think, “Oh crap, my whole string’s gonna lose that.” But hold up — let’s do the math for a typical residential string. A 10-panel string, each at 30V? That’s 300V total. A 0.3V drop across one diode is less than 0.1% of total voltage. For a 20-panel string? Same thing — 0.3V out of 600V is still nothing. The problem isn’t the diode itself dropping a little voltage — it’s which diodes you use and how they’re installed.

Let’s talk about the mistakes I see all the time. A few months back, a small installer in Texas hit me up, saying their 12-panel string was running 4V lower than specs. Turned out, they cheaped out on generic through-hole diodes instead of PV-rated power diodes. Those old silicon diodes have a 0.7V drop — and if they hooked up two diodes per string (one on each end, for some reason I still can’t figure out?), that’s 1.4V right there, plus maybe another drop from a bad connection. Wait, connections matter too. If your diode isn’t crimped or soldered correctly, you get contact resistance, which adds a whole extra voltage drop that has nothing to do with the diode itself. That’s a big one — I’ve seen installers skip the heat shrink or use cheap crimp connectors, and end up with 2V extra drop just from a bad connection. So when someone asks me, “Do blocking diodes cause voltage drop?” my first follow-up is always, “Which diodes are you using, and how’s your wiring?”

Another scenario: shaded strings. Let’s say you have a string of 15 panels, and one gets shaded. Without a blocking diode, that shaded panel becomes a load, pulling power from the other 14 — that’s reverse current flow, which can damage panels or inverters. The blocking diode stops that cold, but here’s where people mix up “voltage drop” with “power loss.” The forward voltage drop of the diode is a small amount of power lost as heat, not a big voltage hit to your system. The real power loss from shading is way bigger than the diode’s drop. I had a commercial client in Arizona a few years ago who skipped diodes on a 50-panel array, and after a single cloudy day, they lost 12% of their output because of reverse current flow. That’s way worse than the 0.3V drop from a single power Schottky diode.

Wait, let’s get into the science to back this up, because I hate giving answers without proof. Blocking diodes are mounted either in the combiner box (string diodes) or at each panel (bypass diodes — wait, hold on, bypass vs blocking, I should clarify that for anyone confused. Bypass diodes are for shaded panels, blocking diodes are for reverse current — two different jobs, but people lump them together. I get it, it’s easy to mix up). The forward voltage (Vf) is the key here. For PV applications, you need diodes rated for high current (like 10A or 20A per string) because solar panels output a lot of current. Generic diodes rated for low current will have a higher Vf and run hotter, which makes the drop worse. The Schottky diodes we sell at my module have a lower Vf, so they’re the go-to for PV because they minimize that loss.

I remember a customer last year who was swapping out diodes in an old system that was underperforming. He was using old silicon diodes from a hardware store, not PV-specific ones. When he replaced them with our Schottky blocking diodes, his string voltage jumped by 0.4V — that’s a real-world win. He told me that translated to an extra 3% more power from his system, which added up to $200 extra a year in electricity savings. That’s exactly why I tell people: don’t blame the diode’s voltage drop, blame using the wrong diode.

Now, let’s address the myth that blocking diodes cause significant voltage drop in large arrays. Let’s take a 1000kW commercial array, split into 20 strings of 25 panels each. Each string has one blocking diode. A standard power Schottky diode has a Vf of 0.3V. Total voltage drop across all diodes in the entire array? 20 x 0.3V = 6V. The total system voltage at MPP (maximum power point) is around 600V, so that’s a 1% loss. Compare that to if you skipped diodes entirely and lost 10-15% from reverse current flow — it’s a no-brainer. The small diode drop is worth it to protect your panels and your system’s long-term health.

Wait, what about when diodes fail? That’s another common question. If a blocking diode goes bad (short or open), that causes its own issues — open diodes kill the string’s current, short diodes can cause reverse current. But a failing diode isn’t the same as normal voltage drop. I’ve had a few customers call saying their diode “caused a voltage drop,” but it turned out the diode was already broken, not just doing its job.

Let’s also talk about installation best practices, because that’s half the battle. First, use PV-rated blocking diodes, not generic ones. Look for ones with low Vf (0.3V or less) and high current ratings matching your string. Second, make sure connections are clean and tight — no rusty lugs, no loose crimps. Third, mount diodes in a well-ventilated area — heat increases forward voltage drop, so if your diode is overheating because it’s crammed in a tight combiner box, the drop will be higher. I always recommend adding a small fan or leaving extra space in the combiner box for airflow.

A lot of new installers I train skip this step, and then end up troubleshooting “voltage drop” when it’s just poor diode selection and bad wiring. That’s why I love what I do — helping people pick the right diodes and install them correctly so their systems run at peak performance.

Now, let’s wrap this up so it’s not just a long list of facts. The short answer to “Can blocking diodes cause voltage drop in a PV system?” is yes — but only a tiny one, if you use the right diodes and install them right. The real issues that cause big voltage drops are cheap, generic diodes, loose connections, overheating, or skipping diodes entirely and suffering reverse current damage. At the end of the day, blocking diodes are essential for protecting your solar investment, and their small forward voltage drop is a trivial cost compared to the power they prevent you from losing to reverse current or panel damage.

Industrial Rectifiers If you’re dealing with voltage drop issues in your PV system, or you’re not sure which blocking diodes are right for your setup, don’t guess. Reach out, and we can chat through your array size, string voltage, and needs to make sure you’re getting the right diodes to keep your system running strong. No sales pitch, just real advice from someone who’s been in the solar diode game for years and worked with hundreds of installers and system owners.

References

  1. Ferial, M. A., et al. (2019). Power Loss Analysis of Blocking Diodes in Photovoltaic Systems. Journal of Renewable and Sustainable Energy, 11(3), 035901.
  2. Solar Energy Industries Association (SEIA). (2021). PV System Component Installation Best Practices: Diodes and Wiring. SEIA Technical Report.
  3. Rashid, M. H. (2017). Power Electronics Handbook: Devices, Circuits, and Applications (4th ed.). Elsevier.

Zhejiang Huixin Semiconductor Co., Ltd.
As one of the most professional solar photovoltaic diode module manufacturers and suppliers in China, our products have good reputation in the market. Please rest assured to buy advanced solar photovoltaic diode module in stock here from our factory. All customized power semiconductors are with high quality and competitive price.
Address: Huixin Semiconductor, No.19 Keais Road, Xiangyang Industrial Zone, Liushi Town, Yueqing City, Wenzhou, Zhejiang Province
E-mail: hx@huixinscr.com
WebSite: https://www.huixinscr.com/